Split Boot – CV Boot Kit (Universal Fit)

$60.50

Bailcast – Made in Britain, Trusted Globally

British-made quality. Proven design. No driveshaft removal required.

The Bailcast CVS18 Split CV Boot Kit is a high-quality, UK-manufactured solution for replacing damaged CV joint boots without removing the driveshaft. Its proven tongue-and-groove design bonds securely using the supplied specialist adhesive.

  • No driveshaft removal – saves installation time and labour.
  • Complete repair kit – includes adhesive, grease, clamps and gloves.
  • Proven British engineering – quality manufacturing from established UK specialist Bailcast.

Important: Check CV boot dimensions before ordering.

Made in the UK – Bailcast British manufactured CV boots

Description

Bailcast Split CV Boot Kit – Universal Glue-On CV Boot

The Bailcast CVS18 Split CV Boot Kit provides a practical way to replace damaged CV joint boots without removing the driveshaft. Manufactured in the UK, this universal glue-on CV boot suits professional workshops and DIY mechanics seeking a convenient, reliable repair method.

Unlike conventional one-piece CV boots, the CVS18 features a full-length tongue-and-groove seam. This allows you to wrap the boot around the driveshaft and join the seam using the supplied specialist adhesive. As a result, you can avoid extensive dismantling on compatible vehicles.

Replace a CV Boot Without Removing the Driveshaft

Traditional CV boot replacement often requires removing the driveshaft or separating the CV joint. However, the Bailcast split boot offers a simpler alternative where the existing joint remains mechanically sound.

  • Saves installation time: Avoid unnecessary driveshaft and suspension dismantling.
  • Glue-on design: The tongue-and-groove seam creates a durable adhesive-bonded joint.
  • Protects original components: Retain a serviceable factory CV joint and driveshaft.
  • Flexible construction: Allows normal CV joint movement and articulation.
  • Made in Britain: Manufactured by established UK automotive component specialist Bailcast.

How Does a Glue-On CV Boot Work?

The CVS18 features a precision-designed tongue-and-groove seam along its full length. First, the installer wraps the boot around the driveshaft. The two sides then join progressively using the specialist adhesive supplied in the kit.

Bailcast uses a specially formulated cyanoacrylate adhesive that retains some flexibility, unlike conventional household superglue. Consequently, the bonding system complements the flexible boot material.

Once the seam has bonded, the installer positions the boot over the CV joint, replenishes the grease and secures both ends using the supplied clamps.

Important: Always use the supplied Bailcast adhesive and follow the manufacturer’s fitting instructions.

Bailcast CVS18 Split CV Boot Dimensions

The CVS18 suits a wide range of CV joint applications. However, always check the required dimensions and sealing arrangement before ordering.

Measurement Fitting Range
Driveshaft diameter 18–34 mm
CV joint diameter 60–116 mm
Boot length 58–128 mm

Check dimensions before ordering. Universal fit does not mean every vehicle or CV joint configuration is compatible. Measure the driveshaft, joint housing and required boot length to confirm suitability.

For further guidance, see our CV Boot Size Selection Guide.

What’s Included in the CVS18 Kit?

Each Bailcast CVS18 kit contains the components required for one compatible CV boot replacement:

  • 1 × Bailcast CVS18 universal split CV boot
  • 1 × Specialist CV boot adhesive tube
  • 1 × 30g CV joint grease sachet
  • 1 × Small ear-type retaining clamp
  • 1 × Large ear-type retaining clamp
  • 2 × Protective latex gloves

For best results, use a suitable ear clamp fitting tool to secure the retaining clamps correctly.

How to Install a Bailcast Split CV Boot

Correct preparation and careful adhesive application are essential for a successful repair. Follow these general steps together with Bailcast’s official instructions.

  1. Prepare the vehicle: Securely support the vehicle and gain access to the damaged CV boot.
  2. Remove the old boot: Carefully remove the damaged boot and clamps without damaging the joint or driveshaft.
  3. Clean the joint: Remove contaminated grease and debris. Keep the bonding surfaces clean and dry.
  4. Check the fit: Compare the boot with the original and trim at the appropriate points where necessary.
  5. Glue the seam: Start at the small end. Apply adhesive and assemble the tongue-and-groove seam in approximately 2cm sections, following Bailcast’s instructions.
  6. Complete the bond: Check each joined section, allow the specified bonding time and apply the final bead of adhesive along the completed seam.
  7. Replenish CV grease: Apply the supplied grease directly to the CV joint rather than filling the boot itself.
  8. Position and clamp: Fit the boot over the joint and secure both ends using the supplied clamps and appropriate ear clamp pliers.
  9. Inspect the installation: Check the bonded seam, clamp tension, sealing surfaces and boot clearance.

Installation tip: Keep your hands and bonding surfaces clean and dry. Additionally, gently warming the boot in cold conditions can make assembly easier. Avoid using WD-40 or similar products to clean the joint, as residues can affect the replacement grease.

For complete fitting instructions, refer to the official Bailcast CVS18 product and technical information, including the manufacturer’s installation document.

Can a Split CV Boot Fit Tripod or Trilobal Joints?

Yes. The Bailcast CVS18 can suit compatible tripod or trilobal CV joints when the dimensions and sealing surfaces allow proper installation.

Some tripod joints feature an irregular three-lobed housing rather than a circular sealing surface. Fortunately, a practical installation method can overcome this issue in suitable applications.

Carefully cut away the damaged original boot while leaving its rubber sealing ring on the joint housing. You can then position and clamp the replacement boot over this retained ring, creating a more uniform circular sealing surface.

Before proceeding, check that the original rubber ring remains undamaged, securely seated and suitable for the replacement boot. The completed assembly must provide a reliable seal.

For illustrated instructions, see our guide to replacing tripod and trilobal CV boots.

Note: This guide demonstrates the retained sealing-ring method with STRETCH CV boots. For the CVS18, also follow Bailcast’s separate adhesive-bonding instructions.

Split CV Boots vs STRETCH CV Boots

PTW Tools offers two convenient approaches to replacing CV joint boots without extensive driveshaft dismantling. However, each system uses a different installation method.

  • Bailcast CVS18 Split CV Boot: Wraps around the driveshaft and uses a specialist adhesive to bond its full-length tongue-and-groove seam.
  • STRETCH CV Boots: Use a highly flexible material that expands over compatible CV joints with a fitting cone or pneumatic installation tool.

Therefore, the Bailcast CVS18 is particularly useful when the installer prefers a wrap-around repair rather than stretching a one-piece boot over the joint.

Important: Do not install the CVS18 using pneumatic CV boot expansion tools or stretch-fitting cones.

Explore our CV boot range and fitting options to compare the available products and installation methods.

Why Choose a British-Made Bailcast CV Boot?

Bailcast is an established British manufacturer specialising in automotive protective boots and related components. Its CVS18 split boot combines purpose-designed flexible material with a proven tongue-and-groove bonding system.

For an otherwise serviceable CV joint, the CVS18 provides a practical way to renew the protective boot while retaining the original driveshaft assembly.

With genuine UK manufacturing, convenient installation and a complete repair kit, the Bailcast CVS18 offers an effective alternative to conventional CV boot replacement.